Opti-ups TS2250B Bedienungsanleitung PDF herunterladen

+++

**)

Placement

This UPS is intended for indoor use

only; its internal components are not

sealed from the environment.

Please install it in a protected

environment away from excessive heat

or excessive moisture.

Charging the UPS first

The battery is fully charged at the

factory. However, it is recommended to

charge the battery at least 8 (eight)

hours before using the UPS, since

energy loss may have occurred during

shipping or long duration storage. To

recharge the battery, simply leave the

UPS plugged into an AC outlet.

Connecting your equipment to the UPS

For UPS models with US-type outlets: connect the power cord(s) of your computer

equipment to the output receptacle(s) of the UPS.

For UPS with IEC outlets, as shown in the illustration, use your computer power cord to

connect UPS to the wall socket. Use the power cord supplied with the UPS to connect

your PC to one of UPS outlets (item 1.5 on the rear panel drawing below).

Turn on the UPS

To turn UPS on please press the power button for 3 seconds. Pressing the power button

shortly under normal mode will enable the self-test function. The silence function can be

enabled/disabled by shortly pressing the power button in backup mode. In addition, the

power button can be used as the master on/off switch for your equipment by leaving your

equipment connected to UPS and switched on. To turn off the UPS, please press power

button for about 3 seconds.

Warning

DO NOT PLUG LASER PRINTERS INTO THE UPS BECAUSE

THEY TYPICALLY DRAW TOO MUCH POWER

Fuse replacement procedure

(Note: for 220V/230V/240V units only)

1. Use a slotted screwdriver to take out the fuse holder

2. Take out the busted fuse from the fuse holder

3. Use the screwdriver to push out the spare fuse from the holder

4. Put the spare fuse in the holder

5. Push the fuse holder back into the AC input socket

6. Follow the UPS turn on procedure

Battery replacement procedure

Note: Follow this procedure for safe replacement of the battery. However, small sparks may occur

during the process. This is normal.

1. Turn off the UPS and unplug it from the wall outlet

2. Remove two screws both sides nearby the front panel

3. Gently pull the top portion of the front panel until it unsnaps

4. Place the front panel on top of the unit taking care not to pull out the wires for the panel

5. Remove the screw for the battery cover

6. Gently pull out the batteries using the tab located at the base of the battery

7. Disconnect the two long wires connecting the batteries to the UPS

8. Use the short wire to connect between the batteries and push the new batteries into place

9. Connect the long wires to the new batteries, making sure that the red wire is connected to the red

battery terminal of the lower battery and the black wire to the black battery terminal of the upper

battery

10. Mount the battery cover and replace the screw

11. Snap back the front panel into place

12. Follow the UPS turn on procedure

Front & Rear Panels

1.1 Power Button 1.5 UPS Outlets

1.2 RS-232 Port

1.6 Surge Suppression Outlet

**)

1.3 Phone/LAN Jack

1.7 Circuit Breaker

1.4 AC Input 1.8 AC Fuse

_____________________________________________

TS-B models only

**)

Battery Backup Outlet for TS1700(B) (110V/120V) /

TS2250

(

)

(

110V/120V/220V/230V/240V

)

No Load Shutdown Function

As a battery saving feature, the UPS will automatically turn off if none

of the connected equipment is operating while the UPS is in back-up

mode. Once normal utility power returns, the unit will re-start

automatically. You can disable the “No Load Shutdown” function by

pressing the power button of your switched-off UPS until you hear two

beeps.

Front panel LED (UPS status indicator)

AC Mode

When the LED is continuously lit and the

buzzer is silent, the UPS is in normal mode and

providing power to your equipment. The UPS

will continue to filter electrical noise and

provide surge protection.

Battery Mode

When the LED blinks every 2 seconds in time

with the beeping sound, the UPS is providing

power from its battery.

Fault

When the LED is flashing rapidly and the

beeping sound is continuous, it indicates that

the UPS is overloaded.

www.opti-ups.com

Thunder Shield

User Manual

1 2

Inhaltsverzeichnis

Seite 1 - Thunder Shield

+++ **)Placement This UPS is intended for indoor use only; its internal components are not sealed from the environment. Please install it in

Seite 2 - Specifications

OPTI-UPS USA: Tel: +1-909-869-5700 Fax: +1-909-869-5730 Toll Free: (888) OPTI-UPS [email protected] http://www.opti-ups.com OPTI-UPS UK: Tel: +44 020

Verwandte Modelle: TS2250 | TS1700B | TS1700 | TS1250 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Opti-ups TS2250B Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Stromversorger Opti-ups TS2250B herunter. OPTI-UPS TS2250B User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: TS2250 | TS1700B | TS1700 | TS1250 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Stromversorger Opti-ups TS2250B